healingiorew.blogg.se

1. #Default route to internet on router on a stick how to#
2. #Default route to internet on router on a stick install#
3. #Default route to internet on router on a stick password#
4. #Default route to internet on router on a stick free#

Reply from 10.0.5.10: bytes=32 time=1ms TTL=127Īs you can see from the output above, the response was received, which means that the hosts can communicate even though they are in different VLANs. To test whether the intervlan communication works, we can try to ping Host C from Host A: C:\>ping 10.0.5.10 In the output above you can see that the router’s physical interface Gi0/0 was divided into three subinterfaces that were then configured as trunk interfaces and assigned the IP addresses. %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.3, changed state to up %LINK-5-CHANGED: Interface GigabitEthernet0/0.3, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.2, changed state to up %LINK-5-CHANGED: Interface GigabitEthernet0/0.2, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0.1, changed state to up %LINK-5-CHANGED: Interface GigabitEthernet0/0.1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to up %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to up Now, let’s configure the router: R1(config)#int Gi0/0 Other ports were configured as access ports and placed into respective VLANs since they are connected to end devices. Notice how we’ve configured the Fa0/1 port on a switch (the port connected to the router’s Gi0/0 interface) as the trunk port. But first, here is the configuration of the switch: SW1(config)#int fa0/3 Each host is in a different VLAN, so we need to divide the physical router’s interface Gi0/0 into logical interfaces, one for each VLAN. We have a network of three hosts, a switch and a router. We will use the following network in our example: (config-subif)# ip address IP_ADDRESS SUBNET_MASK – sets the IP address for the subinterface.

(config-subif)# encapsulation dot1q VLAN_ID – sets the subinterface to trunk and associates it with a specific VLAN.(config)# interface TYPE NUMBER.SUBINTERFACE – creates the subinterface and enters the subinterface command mode.Learn static and default routing configurations on Cisco router.

#Default route to internet on router on a stick how to#

To configure trunking on a router, the following commands are used: In this step by step guide, you will learn how to configure static and default route on Cisco routers. For example, the command i nterface Gi0/0.1 creates a subinterface. The subinterface number begins with the period and it is usually the same as the VLAN the subinterface will be in. The physical interface is divided into logical interfaces (known as subinterfaces), one for each VLAN.Ī subinterface is created with the interface TYPE NUMBER.SUBINTERFACE command. This method of interVLAN communication is called router on a stick (ROAS) and enables all VLANs to communicate through a single physical interface. To allow interVLAN communication, you can divide a single physical interface on a router into logical interfaces that will be configured as trunk interfaces.

#Default route to internet on router on a stick free#

If you are studying for the exam feel free to skip this article. However, these credentials may vary depending upon the maker of the router.This topic is not included in the latest version of the CCNA exam (200-301).

#Default route to internet on router on a stick password#

#2) Generally, for most of the routers, the default username and password is “admin” and “admin”.

#Default route to internet on router on a stick install#

#1) The default username and password can be obtained from the router manual which comes with the router when you first purchase and install it. Where can i find the default username and password for router? If you forgot the password of your router then you can reset the password of the router to it’s default username and password “admin” and not password. Now open the browser and type the IP address of router “192.168.0.1” and enter the default admin name and password. How to reset the password of your router? The default Nokia G-240W-B Router Username is: admin The default Nokia G-240W-B Router Password is: admin To log in to your Nokia G-240W-B router, enter your username and password, and then click the Login button. Important Note: If you have changed them in the past, you need to enter in those values. Enter Your Nokia Router IP Address Into your web browser's Address Bar What is the default username and password for the nokia g 240w b router? This means that in order to login to them you start with your web browser. This is a complete list of user names and passwords for Nokia routers.